Skip to content
TaskNinja

HomeToolsETABS ViewerETABS E2K to PDF

ETABS E2K to PDF

E2K to PDF turns an ETABS .e2k (or SAP2000 .s2k) model into a printable PDF report with the view you set up, the stories table, the section and slab take-off and the load combinations, made in this browser.

EtabsOpenFreeNo signupOn your device
Opening the tool…

What this tool does

Convert an ETABS .e2k model to a PDF report without ETABS: 3D view or story plan, stories, section and slab take-off and load combinations, in your browser.

How to use it

  1. Choose the ETABS .e2k or .$et file, or a SAP2000 .s2k file. Nothing is uploaded.

  2. Set up the picture you want on the first page: the 3D view, an elevation, or one story's plan from the story list. Turn slabs and walls or labels on or off.

  3. Press Download PDF report. Page one has the view and the key numbers; the next pages have the tables.

  4. Need the numbers in Excel instead? Use Take-off CSV, Frames CSV or Points CSV.

Common uses

Review meetings, approvals and site files usually want paper or a PDF, not a model file. Printing from ETABS needs the program and a licence, and screenshots lose the numbers. This page makes an A4 landscape PDF report from the text model in a few seconds on any computer.

The first page is the view you choose, drawn sharp at print resolution, with the program version, units, the counts of stories, columns, beams, braces, slabs and walls, supports, and the overall size of the building. Following pages list every story with its height, level and object counts, each frame section with count, length, concrete volume and steel weight, each slab, deck and wall property with area and volume, the load patterns and each combination with its factors.

Typical uses are a quick quantity cross-check for a BOQ, a model summary for a proof checker or the client, a record of what was in a model at a revision, and a handout for students learning how an ETABS building is set up. Make one PDF per story plan if you want a set of framing plans.

The same numbers are in the take-off CSV for Excel, so you can add rates or compare two revisions side by side.

Story names, section names and load combination names are printed exactly as the modeller typed them, so the report matches the ETABS model tree and the drawings. Accented names written in the Windows code page that older ETABS versions use are read correctly, and very large towers with tens of thousands of frames still fit, because the tables are summarised by section and story rather than listing every object.

Private, and the limits

The PDF is built in this browser with the open source pdf-lib library. The model file and the report never leave your device, and no copy is kept after you close the tab.

The report describes the model as defined in the file. It is not a design report, carries no analysis results and does not replace the engineer's own calculations.

Official sources

Last checked 2026-11-10.

FAQ

Can I make a PDF of one floor plan?
Yes. Pick the story in the story list so only that floor is drawn, press Plan, then Download PDF report. Repeat for each story you need.
Are text labels on the drawing?
Turn on Frame labels or Point labels before you save and they are printed on the view. On a busy 3D view, labels read best on a single story plan.
Does the PDF include design results?
No. A .e2k text model has no results, so the report covers geometry, sections, quantities and loads only.
Which paper size is used?
A4 landscape. The view is scaled to fit the page and the tables flow over as many pages as the model needs.
Does it work for a SAP2000 model?
Yes. Open the .s2k file the same way. A SAP2000 model has no stories, so the report skips the stories table and lists joints, frames and areas instead.
Can I get the take-off in Excel?
Yes. Take-off CSV opens in Excel with three tables: frame sections, slab and wall properties, and stories, all in the model's units.

Related tools

ETABS ViewerSAP2000 ViewerSTAAD File ViewerAll tools